Hikey960：修訂間差異

出自flip the world
← 較舊編輯
Tommy​（留言 | 貢獻）
行政員、​介面管理員、​管理員
586筆編輯
無編輯摘要
Tommy​（留言 | 貢獻）
行政員、​介面管理員、​管理員
586筆編輯
Refactor: add [[Category:Boards and SoCs ]]
 
（未顯示同一使用者於中間所作的 13次修訂）
第3行： 第3行：


== Pin definition ==
== Pin definition ==
[[file:Hikey960-pin-def.jpg]]
* UART signals are driven at 1.8V.
== Build FW ==
* Download the Android source tree:
** repo init -u https://android.googlesource.com/platform/manifest -b master
** repo sync -j8
*Build:
** . ./build/envsetup.sh
** lunch hikey960-userdebug
** make -j24
== Installing initial images ==
*Select fastboot mode by turning ON switch 3 (for details, refer to the HiKey 960 Getting Started guide).
*Power the board.
*Flash initial images:
** cd device/linaro/hikey/installer/hikey960
*Turn OFF switch 3 and power cycle the board.
== Flashing images ==
*Enter fastboot mode by turning ON switch 3.
*Flash images by running the following commands:
** fastboot flash boot out/target/product/hikey960/boot.img
*Turn OFF switch 3 and power cycle the board.
== Building the kernel ==
*Run the following commands:
**mkdir repo-common
**cd repo-common
**repo init -u https://android.googlesource.com/kernel/manifest -b hikey-linaro-android-4.19
**repo sync -j8 -c
**rm -rf out
**rm build.config
**BUILD_CONFIG=hikey-linaro/build.config.hikey960 ./build/build.sh
*Update the kernel in the boot image.
**Copy hi3660-hikey960.dtb (out/android-hikey-linaro-4.19/dist/hi3660-hikey960.dtb) to the hikey-kernel directory as file hi3660-hikey960.dtb-4.19.
**Copy the Image file (out/android-hikey-linaro-4.19/dist/Image.gz-dtb) to the hikey-kernel directory as file Image.gz-dtb-hikey960-4.19.
<pre>
<pre>
HiKey960 Signals 96Boards Signals PIN PIN 96Boards Signals HiKey960 Signals
cp repo-common/out/android-hikey-linaro-4.19/dist/hi3660-hikey960.dtb hikey960/device/linaro/hikey-kernel/hi3660-hikey960.dtb-4.19
GND GND 1 2 GND GND
cp repo-common/out/android-hikey-linaro-4.19/dist/Image.gz-dtb hikey960/device/linaro/hikey-kernel/Image.gz-dtb-hikey960-4.19
UART3_CTS_N UART0_CTS 3 4 PWR_BTN_N PWRON_N
</pre>
UART3_TXD UART0_TxD 5 6 RST_BTN_N EXP_RSTOUT_N
*Make the boot image:
UART3_RXD            UART0_RxD      7    8    SPI0_SCLK      SPI2_CLK         
**make bootimage -j24
UART3_RTS_N          UART0_RTS      9    10   SPI0_DIN      SPI2_DI           
 
UART6_TXD            UART1_TxD      11   12   SPI0_CS        SPI2_CS_N         
== Enable UART ==
UART6_RXD            UART1_RxD      13   14   SPI0_DOUT      SPI2_DO           
* In repo-common/hikey-linaro
I2C0_SCL              I2C0_SCL      15   16   PCM_FS        GPIO_195_I2S0_XFS 
<pre>
I2C0_SDA              I2C0_SDA      17   18   PCM_CLK        GPIO_194_I2S0_XCLK 
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
I2C7_SCL              I2C1_SCL      19   20   PCM_DO        GPIO_193_I2S0_DO   
index 80334e500..a2f1de30b 100644
I2C7_SDA              I2C1_SDA      21   22   PCM_DI        GPIO_192_I2S0_DI   
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
GPIO_208              GPIO-A        23   24   GPIO-B        GPIO_209         
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
GPIO_210              GPIO-C        25   26   GPIO-D        GPIO_211         
@@ -494,7 +494,7 @@
GPIO_212              GPIO-E        27   28   GPIO-F        LCD_BL_PWM       
                        clock-names = "uartclk", "apb_pclk";
LCD_TE0 GPIO-G 29 30 GPIO-H GPIO_040_LCD_RST_N
                        pinctrl-names = "default";
GPIO_052_CAM0_RST_N     GPIO-I        31   32   GPIO-J        GPIO_019         
                        pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
GPIO_075_CAM1_RST_N     GPIO-K        33   34   GPIO-L        GPIO_021         
-                       status = "disabled";
VOUT11_1V8/2V95 +1V8 35 36 SYS_DCIN SYSDC_IN
+                      status = "ok";
SYS_5V +5V 37 38 SYC_DCIN SYSDC_IN
                };
GND GND 39 40 GND GND
 
                uart1: serial@fdf00000 {
@@ -508,7 +508,7 @@
                        clock-names = "uartclk", "apb_pclk";
                        pinctrl-names = "default";
                        pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
-                       status = "disabled";
+                       status = "ok";
                };
 
                uart2: serial@fdf03000 {
</pre>
</pre>
== SDK Architecture ==
[[File:MT7697_SDK_architecture.PNG|MT7697 SDK Arch]]
== Build FW ==
* ./build.sh linkit7697_hdk freertos_ledcube
* Or, go to the mt7697/project/linkit7697_hdk/templates/freertos_ledcube/GCC, then, make
== FW Programming ==
* git clone https://github.com/MediaTek-Labs/mt76x7-uploader
* python ./upload.py -c /dev/ttyUSB0 -f ./out/linkit7697_hdk/freertos_ledcube/freertos_ledcube.bin -t cm4 -p mt7697


== module ON or OFF feature option ==
== Setting the serial number ==
* Edit inc/hal_feature_config.h in each example code
=== To set the random serial number, run ===
**fastboot getvar nve:SN@16\_DIGIT\_NUMBER
*Bootloader exports the generated serial number to the kernel using androidboot.serialno=.


=== Setting monitor resolution ===
*Edit the device/linaro/hikey/hikey960/BoardConfig.mk parameter BOARD_KERNEL_CMDLINE and configure the video setting. For example, the setting for a 24-inch monitor is video=HDMI-A-1:1280x800@60.


== Note ==
== Android note ==
* Disable ICMP for enable ping
* Disable ICMP for enable ping
** sysctl -w net.ipv4.icmp_echo_ignore_all=0
** sysctl -w net.ipv4.icmp_echo_ignore_all=0
第46行： 第92行：
* [https://source.android.com/setup/build/devices, Build steps]
* [https://source.android.com/setup/build/devices, Build steps]
* [https://snapshots.linaro.org/96boards/hikey960/linaro/aosp-master/latest/, Pre build image]
* [https://snapshots.linaro.org/96boards/hikey960/linaro/aosp-master/latest/, Pre build image]
[[Category:Boards and SoCs]]

2026年8月21日 (五) 13:17的最新修訂

Hikey960 Front Hikey960 Back

Pin definition

  • UART signals are driven at 1.8V.

Build FW

  • Build:
    • . ./build/envsetup.sh
    • lunch hikey960-userdebug
    • make -j24

Installing initial images

  • Select fastboot mode by turning ON switch 3 (for details, refer to the HiKey 960 Getting Started guide).
  • Power the board.
  • Flash initial images:
    • cd device/linaro/hikey/installer/hikey960
  • Turn OFF switch 3 and power cycle the board.

Flashing images

  • Enter fastboot mode by turning ON switch 3.
  • Flash images by running the following commands:
    • fastboot flash boot out/target/product/hikey960/boot.img
  • Turn OFF switch 3 and power cycle the board.

Building the kernel

  • Run the following commands:
  • Update the kernel in the boot image.
    • Copy hi3660-hikey960.dtb (out/android-hikey-linaro-4.19/dist/hi3660-hikey960.dtb) to the hikey-kernel directory as file hi3660-hikey960.dtb-4.19.
    • Copy the Image file (out/android-hikey-linaro-4.19/dist/Image.gz-dtb) to the hikey-kernel directory as file Image.gz-dtb-hikey960-4.19.
 cp repo-common/out/android-hikey-linaro-4.19/dist/hi3660-hikey960.dtb hikey960/device/linaro/hikey-kernel/hi3660-hikey960.dtb-4.19
 cp repo-common/out/android-hikey-linaro-4.19/dist/Image.gz-dtb hikey960/device/linaro/hikey-kernel/Image.gz-dtb-hikey960-4.19
  • Make the boot image:
    • make bootimage -j24

Enable UART

  • In repo-common/hikey-linaro
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 80334e500..a2f1de30b 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -494,7 +494,7 @@
                        clock-names = "uartclk", "apb_pclk";
                        pinctrl-names = "default";
                        pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
-                       status = "disabled";
+                       status = "ok";
                };

                uart1: serial@fdf00000 {
@@ -508,7 +508,7 @@
                        clock-names = "uartclk", "apb_pclk";
                        pinctrl-names = "default";
                        pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
-                       status = "disabled";
+                       status = "ok";
                };

                uart2: serial@fdf03000 {

Setting the serial number

To set the random serial number, run

    • fastboot getvar nve:SN@16\_DIGIT\_NUMBER
  • Bootloader exports the generated serial number to the kernel using androidboot.serialno=.

Setting monitor resolution

  • Edit the device/linaro/hikey/hikey960/BoardConfig.mk parameter BOARD_KERNEL_CMDLINE and configure the video setting. For example, the setting for a 24-inch monitor is video=HDMI-A-1:1280x800@60.

Android note

  • Disable ICMP for enable ping
    • sysctl -w net.ipv4.icmp_echo_ignore_all=0

Reference

取自「https://tommy0804.ddns.net/index.php?title=Hikey960&oldid=538」